Because traffic between the local GATT client(s) and
remote servers are subject to different controls than
remote clients and the local server, all on the shared
fixed CID, it is important to manage the traffic on
seperate sockets.
Change-Id: I62385143c86522f4b123b32592b69f2a0ae6dc76
CRs-fixed: 336029
Signed-off-by: Brian Gix <bgix@codeaurora.org>
We only support a 23 octet MTU, so auto-respond to all
MTU change requests with the 23 octet response.
Change-Id: Ic69d5f068759d983f8cd98b329acbb9d3a481c49
CRs-fixed: 336025
Signed-off-by: Brian Gix <bgix@codeaurora.org>
When doing L2CAP configuration, use the correct retransmit and monitor
timeouts when configuring (or reconfiguring) AMP channels. The host
stack needs to use the timeouts read from incoming configuration
responses, and write appropriate timeouts when sending configuration
responses.
Change-Id: I1271ade93dbfee58a1cac115280704a327e901b2
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Added Flush Timeout parameter setting for l2cap channel. Bluetooth
profiles using l2cap can set this parameter to flush out the data
when it cannot be sent over the air with in timeout duration.
Change-Id: I60420c5be3a790aff26bc30e8089fdca47a99222
Signed-off-by: Srinivas Krovvidi <skrovvid@codeaurora.org>
Timer that was started at beginning of LE Pairing did not correctly
terminate pairing process when it fired, and was not properly cleaned
up on pairing completion.
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Enabled ECB Block encoding for Low Energy pairing
Implemented missing components of MGMTOPS interface
Differentiated as needed between BR/EDR pairing and LE pairing
Signed-off-by: Brian Gix <bgix@codeaurora.org>
Conflicts:
net/bluetooth/mgmt.c
The ERTM receive buffer is now handled in a way that does not require
the busy queue and the associated polling code.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This change moves most L2CAP ERTM receive buffer handling out of the
L2CAP core and in to the socket code. It's up to the higher layer
(the socket code, in this case) to tell the core when its buffer is
full or has space available. The recv op should always accept
incoming ERTM data or else the connection will go down.
Within the socket layer, an skb that does not fit in the socket
receive buffer will be temporarily stored. When the socket is read
from, that skb will be placed in the receive buffer if possible. Once
adequate buffer space becomes available, the L2CAP core is informed
and the ERTM local busy state is cleared.
Receive buffer management for non-ERTM modes is unchanged.
Signed-off-by: Mat Martineau <mathewm@codeaurora.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Instead of setting bits manually we use set_bit, test_bit, etc.
Also remove L2CAP_ prefix from macros.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch implements a check in smp cmd pairing request and pairing
response to verify if encryption key maximum size is compatible in both
slave and master when SMP Pairing is requested. Keys are also masked to
the correct negotiated size.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Anderson Briglia <anderson.briglia@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch adds support for disconnecting the link when SMP procedure
takes more than 30 seconds.
SMP begins when either the Pairing Request command is sent or the
Pairing Response is received, and it ends when the link is encrypted
(or terminated). Vol 3, Part H Section 3.4.
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
ERTM use the generic L2CAP timer functions to keep a reference to the
channel. This is useful for avoiding crashes.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
We now plan to use l2cap_set_timer and l2cap_clear_timer in ERTM timers.
Change-Id: Ie62b01e003f8885ae89c73e2e64195c21cbadddd
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
struct l2cap_chan has now its own refcnt that is compatible with the
socket refcnt, i.e., we won't see sk_refcnt = 0 and chan->refcnt > 0.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Now socket state is tracked by struct sock and channel state is tracked by
chan->state. At this point both says the same, but this is going to change
when we add AMP Support for example.
Change-Id: Idbf873f5e8dd94f5b2482ba960c52193d28ce5dd
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add an abstraction layer between L2CAP core and its users (only
l2cap_sock.c now). The first function implemented is new_connection() that
replaces calls to l2cap_sock_alloc() in l2cap_core.c
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add BT_POWER socket option used to control the power
characteristics of the underlying ACL link. When the remote end
has put the link in sniff mode and the host stack wants to send
data we need need to explicitly exit sniff mode to work well with
certain devices (For example, A2DP on Plantronics Voyager 855).
However, this causes problems with HID devices.
Hence, moving into active mode when sending data, irrespective
of who set the sniff mode has been made as a socket option. By
default, we will move into active mode. HID devices can set the
L2CAP socket option to prevent this from happening.
Currently, this has been implemented for L2CAP sockets. This has been
tested with incoming and outgoing L2CAP sockets for HID and A2DP.
Based on discussions on linux-bluetooth and patches submitted by
Andrei Emeltchenko.
Signed-off-by: Jaikumar Ganesh <jaikumar@google.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The call to l2cap_chan_clear_timer() is not really needed in l2cap_sock.c.
This patch also adds a call to l2cap_chan_clear_timer() to the only place
in __l2cap_sock_close() that wasn't calling it. It's safe call it there
because l2cap_chan_clear_timer() check first for timer_peding().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The new timer does not belong to struct sock, tought it still touch some
sock things, but this will be sorted out soon.
Change-Id: I55dc122657f3b8e80e76acf8c479e2d5c9889af5
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
chan_type says if our chan is raw(direclty access to HCI),
connection less or connection oriented.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This move all the sending logic to l2cap_core.c, but we still have a
socket dependence there, struct msghdr. It will be removed in some of the
further commits.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This is actually __l2cap_sock_close() renamed to __l2cap_chan_close().
At a first look it may not make sense, but with the further cleanups that
will come it will.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
A new list was added to replace the socket based one. This new list
doesn't depent on sock and then fits better inside l2cap_core.c code.
It also rename l2cap_chan_alloc() to l2cap_chan_create() and
l2cap_chan_free() to l2cap_chan_destroy)
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
When the user doesn't specify a psm we have the choose one for the
channel. Now we do this inside l2cap_add_psm().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The intention is to get rid of the l2cap_sk_list usage inside
l2cap_core.c. l2cap_sk_list will soon be replaced by a list that does not
depend on socket usage.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
There is no need to the socket deal directly with the channel, most of the
time it cares about the channel only.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
In this commit, omtu, imtu, flush_to, mode and sport. It also remove the
pi var from l2cap_sock_sendmsg().
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
l2cap_chan_connect() is a much better name and reflects what this
functions is doing (or will do once socket dependence is removed from the
core).
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
If the allocation happens at l2cap_sock_create() will be able to use the
struct l2cap_chan to store channel info that comes from the user via
setsockopt.
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Brian Gix
Mat Martineau
Srinivas Krovvidi
Bryan Huntsman
Gustavo F. Padovan
Vinicius Costa Gomes
Anderson Briglia
Jaikumar Ganesh